There is no definitive answer to this question, as there are pros and cons to both options. Placing the rain gutter under the drip edge can help to prevent leaves and other debris from clogging the gutter, but it can also make the gutter more difficult to clean. Some people also feel that it gives the home a more finished look. Ultimately, it is a matter of personal preference and what works best for your home.

How do you use drip edge with gutters?

Drip edge is installed under the shingles and along the gutter’s edge. The drip edge’s purpose is to direct water into the gutter and keep water from running behind the gutter and causing rot and other damage.
Drip edge is available in a variety of colors to match your shingles and gutters. It is important to choose the right size drip edge for your gutters.

To install drip edge, first remove the old drip edge and clean the area. Then, measure and cut the new drip edge to fit. Nail the drip edge in place, making sure the nails are driven into the fascia board and not the shingles.
Once the drip edge is in place, you can install the gutters. Start by attaching the hangers to the fascia board. Then, hang the gutters and secure them in place with screws.

How far should drip edge extend into gutter?

Drip edge is a metal flashing that helps to keep water from seeping behind your gutters and causing damage to your home. It is installed along the edge of your roof, and extends out past the gutter about an inch or two. This allows the water to drip off of the roof and into the gutter, instead of running down the side of your house.

Do you install drip edge with gutter apron?

Drip edge is not typically installed with gutter apron. Drip edge is a metal flashing that is installed on the edges of your roof. Its purpose is to direct water away from your roof and into your gutters. Gutter apron is a piece of metal or plastic that is installed under your gutters. Its purpose is to prevent water from seeping behind your gutters and damaging your home.

How far below drip edge is gutter?

There is no definitive answer to this question as it depends on a number of factors, such as the type of gutter, the pitch of the roof, and the amount of rainfall. However, as a general rule of thumb, the gutter should be installed at least 2-3 inches below the drip edge of the roof. This will ensure that the gutter is able to catch the majority of the water that runs off the roof and redirect it away from the home.

How do you stop water leaks between drip edge and gutters?

The first step is to check the gutters and downspouts to see if they are properly installed and in good repair.

If they are, then the next step is to check the drip edge for any cracks or holes.
The third step is to apply a sealant to the drip edge and gutters.
The fourth step is to install a gutter guard or leaf guard.

The fifth and final step is to regularly inspect and clean the gutters and downspouts to prevent any future water leaks.

Where do you put gutter drip edges?

If your home has gutters, they most likely have drip edges. Drip edges are L-shaped metal flashing that extend beyond the gutter’s edge and over the roof decking. The purpose of drip edges is two-fold: to keep water from dripping behind the gutter and to direct the water into the gutter.

Drip edges are installed on the eaves before the roofing is installed. The drip edge should extend at least ¼-inch past the gutter’s edge and 2 to 4 inches over the roof decking. The overhang protects the fascia board and prevents water from seeping under the shingles.

Does drip edge go over or under roll roofing?

Drip edge installation on a roof is very important. It helps to keep water from running under the shingles and causing leaks in the home. The drip edge is installed at the eaves of the roof and extends out past the edge of the roof. It is usually made of metal or plastic and has a lip that hangs over the edge of the roof. The drip edge should always be installed on top of the roll roofing.

Bottom Line

The answer to this question depends on the specific design of your home and rain gutter system. In some cases, the rain gutter may need to go under the drip edge in order to function properly. However, in other cases, it may be better to place the rain gutter above the drip edge. If you’re unsure about which option is best for your home, it’s best to consult with a professional.