A metal drip edge will help protect the sheathing under the roof, but if it’s installed too closely to the fascia board, it can still cause water to be drawn into the fascia. The best installation method is to leave a gap between the drip edge and the fascia board, about the width of a finger.
Does tar paper go over or under drip edge?
If the drip edge is along the eaves of the roof, it goes underneath the felt underlayment. When the drip edge is along the rake edges, it is placed over the felt paper underlayment.
How many nails do you use on drip edge?
Nail the drip edge to the roof deck with minimum 12-gage roofing nails spaced 8 to 10-inches on center and 1-½ to 3-inches from the edge of the sheathing. Adjacent drip edge pieces should be lapped minimum 2 inches.
Do gutters go over or under drip edge?
It is recommended that gutters are placed under or ‘behind’ the drip edge of your roof. A drip edge refers to a component that hangs over the roof and has an outward projecting lower edge.
Should drip line holes up or down?
When laying the drip tape, make sure that the holes are facing up- ward, and that there are no kinks in the line.
How do you install drip edge after roofing?
Make sure the outer edge extends over the gutter. If it doesn’t, pull the drip edge out slightly from under the shingles. Secure the drip edge with roofing cement. Apply a continuous bead of cement along the top of the drip edge, then press down on the shingle.
Do you install drip edge over ice and water shield?
Ice and water protector needs to be installed directly onto the roof deck after you have placed the drip edge at the eave. (The drip edge will be installed over the ice and water protector and other underlayments at roof rake edges.)
Installing drip edge and gutter is a simple and easy process that anyone can do.You will need some basic tools and materials including a level, tape measure, hacksaw, and screws.Begin by measuring the length of your gutter and cutting the…
Begin by measuring the length of your gutter. You will need to purchase a gutter drip edge that is slightly longer than your gutter.Cut the drip edge to size with a hacksaw.Install the drip edge onto the gutter by nailing…
Begin by removing any old drip edge that is already on the gutter. This can be done with a utility knife or a screwdriver.Next, measure the length of the gutter and cut the drip edge to size. Make sure to…
You can install gutter apron over drip edge as long as the drip edge is properly installed and in good condition. The apron will help to protect the drip edge from getting clogged with debris and will also help to…
Most roofers will install drip edge on your home if you request it. Drip edge is a metal flashing that helps to keep water from seeping under your shingles and causing damage to your roof deck or home interior. Should…
How far below the drip edge should the gutter be? There is no definitive answer to this question as it depends on a number of factors, such as the type of roof, the climate, and the amount of rainfall. However,…
Begin by measuring the length of your gutter.Cut the drip edge to size, using a hacksaw or power saw.Install the drip edge by nailing it into the gutter, with the drip edge facing downwards. What is the proper way to…
drip edge is not installed OVER the gutter, but rather underneath it. The drip edge is installed so that the edge of the metal is even with the outside edge of the gutter. The gutter is then installed on top…
Begin by measuring the length of your gutter run. You will need one piece of drip edge for each gutter section.Cut the drip edge to size using a hacksaw or power saw.Install the drip edge onto the gutter run, starting…
Measure the length of your gutter run and cut the gutters to size.Install hangers at the appropriate intervals along the length of the gutter.Suspend the gutters from the hangers and position them so that the lip of the gutter is…
Can drip edge be installed later? Yes, drip edge can be installed later, but it is not recommended. Drip edge should be installed when the roof is being installed to ensure that it is properly installed and does not cause…
Remove any old drip edge and clean the surface.Make sure the new drip edge is the same size and shape as the old one.Nail the new drip edge in place with the nails provided.Make sure the drip edge is properly…
To install a rain gutter with a drip edge, you will need a few tools and materials. A level, tape measure, drill, saw, and screws are required. You will also need to purchase the rain gutter and drip edge from…
Begin by measuring the length of your home’s eaves. This will determine how much gutter material you’ll need to purchase.Next, install the gutter hangers along the length of the eaves. Be sure to space them evenly.Once the hangers are in…
Begin by removing any dirt or debris from the surface of the gutter using a putty knife.Next, use a measuring tape to measure the length of the gutter.Cut a piece of drip edge to the same length as the gutter,…
Begin by measuring the length of your gutters.Cut the drip edge to size using a hacksaw or tin snips.Install the drip edge by nailing it into the front lip of the gutter.Make sure the drip edge is installed flush with…