How To Install Gutter Downspout Extension

  1. Place the gutter downspout extension on the ground next to the gutter.
  2. Center the extension over the downspout opening.
  3. Mark the location of the holes on the extension.
  4. Drill holes at the marked locations.
  5. Attach the extension to the downspout using the screws and washers provided.
  6. Place the end of the extension over the drain pipe or catch basin.
  7. Secure the extension in place with the provided clamps.

Do downspout extenders work?

Downspout extenders are a type of gutter accessory that can be added to a home’s existing gutter system to redirect rainwater runoff away from the foundation and prevent basement flooding. They are most commonly used in areas with a lot of rainfall or where the ground slopes towards the house.

Downspout extenders work by extending the length of the downspout so that water is redirected further away from the foundation. They can be added to both new and existing gutters and are usually made of plastic or metal. Some downspout extenders come with a built-in deflector that helps to keep leaves and debris out of the gutters.

Downspout extenders are a relatively inexpensive way to protect your home from water damage and can be installed by a DIYer with basic handyman skills.

How do you extend downspouts above ground?

One way to extend a downspout above ground is to use a drain pipe extension. This is a simple process that involves attaching the extension to the existing drain pipe. Another way to extend a downspout is to use a downspout adapter. This is a more complex process that involves cutting the existing downspout and attaching the adapter. The third way to extend a downspout is to use a downspout extension kit. This is the most complex process and involves installing a new downspout.

How far should gutter downspout extend from house?

There are a few things to consider when deciding how far to extend your gutter downspouts from your house. The most important factor is the amount of rainfall your area receives. If you live in an area with a lot of rainfall, you’ll want to extend your downspouts further from your house to prevent water from pooling around your foundation. Another factor to consider is the slope of your yard. If your yard slopes away from your house, you’ll want to extend your downspouts to prevent water from running back towards your foundation. Finally, you’ll want to consider the appearance of your downspouts. If you want your downspouts to be less visible, you’ll want to extend them further from your house.

How do downspout elbows attach to gutters?

  1. Locate the desired attachment point on the gutter.
  2. Clean the area around the attachment point to ensure a good seal.
  3. Affix the downspout elbow to the gutter using screws or another type of fastener.
  4. Check to make sure the downspout elbow is secure and does not leak.

How do you anchor downspout extensions?

First, measure the downspout to determine how long the extension will need to be. Cut the extension to size, using a hacksaw.

Next, fit one end of the extension over the top of the downspout, and secure it in place with sheet metal screws. Repeat this process at the bottom of the downspout.

Now, fit the extension into the ground so that it is level and secure. You may need to dig a small trench for the extension to fit into.

Finally, backfill the trench and around the extension, and water the area well to help the soil settle.

How do you keep downspout extensions from blowing away?

The first step is to make sure that your downspout extensions are properly installed. If they are not, they will be more likely to blow away in high winds. Make sure that the brackets are properly attached to the downspouts and that the extensions are snug against the house.

You can also help to keep downspout extensions in place by weighting them down. This can be done by filling the extension with sand or rocks, or by attaching weights to the end of the extension.

Finally, you can also use straps or ties to secure the downspout extension to the house or to other objects nearby. This will help to keep it from blowing away in high winds.

How do I redirect downspout water away from my house?

  1. Begin by ensuring that your gutters are clean and free of any debris.
  2. Next, measure the length of downspout that you will need to redirect the water away from your house.
  3. Cut your downspout to the desired length using a hacksaw.
  4. Drill holes into the bottom of the downspout using a drill bit that is slightly larger than the diameter of your downspout.
  5. Affix the downspout to the side of your house using the holes that you drilled.
  6. Connect a length of PVC pipe to the end of the downspout.
  7. Route the PVC pipe away from your house and to a location where the water can drain away safely.
  8. Secure the PVC pipe in place using zip ties or similar fasteners.
  9. Test the downspout by running water through it to ensure that the water is being redirected away from your house as desired.

Final Talk

If you follow the steps above, you should now have a functioning gutter downspout extension! These are a great way to keep your gutters clean and free-flowing, and can help prevent water damage to your home. Thanks for reading, and we hope this was helpful.